View EJ080NA-05B_7677874.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

chimei inno l u x display corporation lcd module s p e c i f i c at i o n customer: model name: EJ080NA-05B date: 2011/04/28 version: 01 preliminary specification final specification for customer s acceptance approved by comment approved by review ed by prepared by hans chen 2011/05/10 james yu charlie chou 2011/05/09 david lee 2011/04/28 free datasheet http://
6 innolux copyright 2004 all rights reserved, copying forbidden. record of revision version revise date page content pre-spec.01 2011/04/09 initial release. free datasheet http://
chimei inno l u x contents 1. general specifications ............................ ................................................... ............................. 1 2. pin assignment.................................... ................................................... ................................ 2 2.1. tft lcd panel driving section.................. ................................................... ................. 2 3. operation specifications .......................... ................................................... ............................ 5 3.1. absolute maximum rating........................ ................................................... ................... 5 3.1.1. typical operation conditions................. ................................................... .............. 6 3.1.2. current consumption ......................... ................................................... ................. 7 3.1.3. backlight driving conditions ................... ................................................... ............. 7 3.2. power sequence ................................. ................................................... ........................ 8 3.3. timing characteristics .......................... ................................................... ....................... 9 3.3.1. ac electrical characteristics ................... ................................................... ............ 9 3.3.2. timing...................................... ................................................... .......................... 10 3.3.3. timing diagram .............................. ................................................... ................... 11 4. optical specifications............................. ................................................... ............................ 12 5. reliability test items ........................... ................................................... ............................... 16 6. general precautions .............................. ................................................... ............................ 17 6.1. safety ........................................ ................................................... ................................ 17 6.2. handling ...................................... ................................................... .............................. 17 6.3. static electricity ............................... ................................................... .......................... 17 6.4. storage ....................................... ................................................... ............................... 17 6.5. cleaning ...................................... ................................................... .............................. 17 7. mechanical drawing ................................ ................................................... .......................... 18 8. package drawing .................................. ................................................... .............................. 19 8.1 packaging material table......................... ................................................... .................. 19 8.2 packaging quantity ............................... ................................................... .................... 19 8.3 packaging drawing................................ ................................................... .................... 20 free datasheet http://
chimei inno l u x date :2011/04/28 page:1/20 1. general specifications no. item specification remark 1 lcd size 8.0 inch(diagonal) 2 driver element a-si tft active matrix 3 resolution 800 3(rgb) 600 4 display mode normally white, transmissive 5 dot pitch 0.0675(w) 0.2025(h) mm 6 active area 162.0(w) 121.5(h) mm 7 module size 183.0(w) 141.0(h) 5.6(d) mm note 1 8 surface treatment anti-glare 9 color arrangement rgb-stripe 10 interface digital 11 backlight power consumption 1.782w (typ.) 12 panel power consumption 0.356w(typ.) 13 weight tbd note 1: refer to mechanical drawing. free datasheet http://
chimei inno l u x date :2011/04/28 page:2/20 2. pin assignment 2.1. tft lcd panel driving section 1. fpc connector is used for the module electronics int erface. the recommended model is fh12a-50s-0.5sh manufactured by hirose. pin no. symbol i/o function remark 1 led + p led anode 2 led + p led anode 3 led - p led cathode 4 led - p led cathode 5 gnd p power ground 6 v com i common voltage 7 v cc p power for digital circuit 8 mode i de/sync mode select note3 9 de i data input enable 10 vs i vertical sync input 11 hs i horizontal sync input 12 b7 i blue data(msb) 13 b6 i blue data 14 b5 i blue data 15 b4 i blue data 16 b3 i blue data 17 b2 i blue data 18 b1 i blue data 19 b0 i blue data(lsb) 20 g7 i green data (msb) 21 g6 i green data 22 g5 i green data 23 g4 i green data 24 g3 i green data 25 g2 i green data 26 g1 i green data 27 g0 i green data (lsb) 28 r7 i red data (msb) 29 r6 i red data 30 r5 i red data 31 r4 i red data free datasheet http://
chimei inno l u x date :2011/04/28 page:3/20 32 r3 i red data 33 r2 i red data 34 r1 i red data 35 r0 i red data (lsb) 36 gnd p power ground 37 dclk i sample clock 38 gnd p power ground 39 l/r i right/ left selection note2,5 40 u/d i up/down selection note2,5 41 v gh p gate on voltage 42 v gl p gate off voltage 43 av dd p power for analog circuit 44 reset i global reset pin. note1 45 nc - no connection 46 v com i common voltage 47 dithb i dithering function note 4 48 gnd p power ground 49 nc - no connection 50 nc - no connection i: input, o: output, p: power note 1: global reset pin. active low to enter reset st ate. suggest to connecting with an rc reset circuit for stability. normally pull high. note 2: selection of scanning mode setting of scan control input u/d r/l scanning direction gnd v cc up to down, left to right v cc gnd down to up, right to left gnd gnd up to down, right to left v cc v cc down to up, left to right note 3: de/sync mode select, normally pull high. h: de mode. l: hs/vs mode. note4: dithering function enable control. normall y pull high. dithb=1,disable internal dithering fu nction. for 18bit rgb interface, connect two lsb bits of all the r/g/b data buses to gnd. dithb=0,enable internal dithering fu nction, for ttl 24bit parallel rgb image data input. free datasheet http://
chimei inno l u x date :2011/04/28 page:4/20 note 5: definition of scanning direction. refer to the figure as below: free datasheet http://
chimei inno l u x date :2011/04/28 page:5/20 3. operation specifications 3.1. absolute maximum rating ( gnd=av ss =0v, note 1) values item symbol min. max. unit remark v cc -0.3 5.0 v av dd -0.5 13.5 v v gh 13.0 19.0 v v gl -12.0 -2.0 v power voltage v gh -v gl - 31.0 v t op -20 70 operation temperature storage temperature t st -30 80 led reverse voltage v r - 1.2 v each led note 2 led forward current i f - 25 ma each led note 1: the absolute maximum rating values of this pr oduct are not allowed to be exceeded at any times. should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be re covered, or in an extreme case, the module may be permanently destroyed. note 2: v r conditions: zener diode 20ma free datasheet http://
chimei inno l u x date :2011/04/28 page:6/20 3.1.1. typical operation conditions (gnd=av ss =0v, note 1) values item symbol min. typ. max. unit remark v cc 3.0 3.3 3.6 v note 2 av dd 10.2 10.4 10.6 v v gh 15.3 16.0 16.7 v power voltage v gl -7.7 -7.0 -6.3 v input signal voltage v com 2.8 (3.8) 4.8 v note 4 input logic high voltage v ih 0.7v cc - v cc v input logic low voltage v il 0 - 0.3v cc v note 3 note 1: be sure to apply v cc and v gl to the lcd first, and then apply v gh . note 2: v cc setting should match the signals output voltage (refer to note 3) of customers system board . note 3: dclk,hs,vs,rstb,updn,stlr,mode,dithb. note 4: typical v com is only a reference value, it must be optimized accordi ng to each lcm. be sure to use vr; free datasheet http://
chimei inno l u x date :2011/04/28 page:7/20 3.1.2. current consumption (gnd=av ss =0v) values item symbol min. typ. max. unit remark i gh - 0.2 0.5 ma v gh =16.0v i gl - 0.2 1.0 ma v gl = -7.0v i cc - 5.5 10.0 ma v cc =3.3v current for driver iav dd - 32.0 50.0 ma av dd =10.4v 3.1.3. backlight driving conditions values item symbol min. typ. max. unit remark voltage for led backlight v l 9.3 9.9 10.5 v note 1 current for led backlight i l 162 180 198 ma led life time - 20,000 - - hr note 2 note 1: the led supply voltage is defined by the num ber of led at ta=25 and i l =180ma. note 2: the led life time is defined as the module brightness decrease to 50% original brightness at ta=25 and i l =180ma. the led lifetime could be decreased if operating i l is lager than 180 ma. free datasheet http://
chimei inno l u x date :2011/04/28 page:8/20 3.2. power sequence 3.2.1. power on: 3.2.2. power off: note: data include r0~r5, b0~b5, go~g5, stlr,updn, d clk, hs,vs,de. vcc vgl avdd vgh data b/l b/l data vgh avdd vgl vcc free datasheet http://
chimei inno l u x date :2011/04/28 page:9/20 3.3. timing characteristics 3.3.1. ac electrical characteristics values item symbol min. typ. max. unit remark hs setup time t hst 8 - - ns hs hold time t hhd 8 - - ns vs setup time t vst 8 - - ns vs hold time t vhd 8 - - ns data setup time t dsu 8 - - ns data hole time t dhd 8 - - ns de setup time t esu 8 - - ns de hole time t ehd 8 - - ns vdd power on slew rate t por - - 20 ms rstb pulse width t rst 10 - - us clkin cycle time t coh 20 - - ns clkin pulse duty t cwh 40 50 60 % output stable time t sst - - 6 us free datasheet http://
chimei inno l u x date :2011/04/28 page:10/20 3.3.2. timing values item symbol min. typ. max. unit remark horizontal display area thd - 800 - dclk dclk frequency fclk - 40 50 mhz one horizontal line th 862 1056 1200 dclk hs pulse width thpw 1 - 40 dclk hs back porch(blanking) thb 46 46 46 dclk hs front porch thfp 16 210 354 dclk values item symbol min. typ. max. unit remark vertical display area tvd - 600 - th vs period time tv 624 635 700 th vs pulse width tvpw 1 - 20 th vs back porch(blanking) tvb 23 23 23 th vs front porch tvfp 1 12 77 th free datasheet http://
chimei inno l u x date :2011/04/28 page:11/20 3.3.3. timing diagram figure 3.1 input clock and data timing diagram figure 3.2 horizontal input timing diagram. free datasheet http://
chimei inno l u x date :2011/04/28 page:12/20 4. optical specifications values item symbol condition min. typ. max. unit remark l =180(9 oclock) 60 70 - r =0(3 oclock) 60 70 - t =90(12 oclock) 40 50 - viewing angle (cr 10) b =270(6 oclock) 60 70 - degree note 1 t on - 10 20 msec note 3 response time t off - 15 30 msec note 3 contrast ratio cr 400 500 - - note 4 w x 0.26 0.31 0.36 - color chromaticity w y 0.28 0.33 0.38 - note 2 note 5 note 6 luminance l 200 250 - cd/m2 note 6 luminance uniformity y u normal ==0 70 75 - % note 7 test conditions: 1. v cc =3.3v, i l =180ma (backlight current), the ambient temperature is 25 . 2. the test systems refer to note 2. free datasheet http://
chimei inno l u x date :2011/04/28 page:13/20 note 1: definition of viewing angle range fig. 4-1 definition of viewing angle note 2: definition of optical measurement system. the optical characteristics should be measure d in dark room. after 30 minutes operation, the optical properties are measured at the center point of the lcd screen. (response time is measured by photo detector topcon bm-7 , other items are measured by bm-5a/field of view: 1 /height: 500mm. ) fig. 4-2 optical measurement system setup normal line ==0 normal line ==0 photo detector =90 12 oclock direction =270 6 oclock direction =0 =180 active area 500mm lcd panel =90 12 oclock direction =270 6 oclock direction =0 =180 active area l t b r free datasheet http://
chimei inno l u x date :2011/04/28 page:14/20 note 3: definition of response time the response time is defined as the lcd optical switching time interval between white state and black state. rise time (t on ) is the time between photo detector output intensity changed from 90% to 10%. and fall time (t off ) is the time between photo detector output intensity changed from 10% to 90%. fig. 4-3 definition of response time note 4: definition of contrast ratio state black" " the on lcd when measured luminance state white" " the on lcd when measured luminance (cr) ratio contrast = note 5: definition of color chromaticity (cie1931 ) color coordinates measured at center point of lcd. note 6: definition of luminance: measured at the center area of the panel when lcd pan el is driven at white state. the led driving condition is i l =180ma . 100% 90% 10% 0% photo detector output (relative value) t on t off white (tft off) black (tft on) white (tft off) free datasheet http://
chimei inno l u x date :2011/04/28 page:15/20 note 7: definition of luminance uniformity active area is divided into 9 measuring areas (refer t o fig. 4-4 ).every measuring point is placed at the center of each measur ing area. max min b b (yu) uniformity luminance = l-------active area length w----- active area widt h w w/3 w/3 w/6 l/3 l/3 l/6 l fig. 4-4 definition of measuring points b max : the measured maximum luminance of all measurement po sition. b min : the measured minimum luminance of all measurement po sition. free datasheet http://
chimei inno l u x date :2011/04/28 page:16/20 5. reliability test items (note3) item test conditions remark high temperature storage ta = 80 240hrs note 1 note 4 low temperature storage ta = -30 240hrs note 1 note 4 high temperature operation ts = 70 240hrs note 2 note 4 low temperature operation ta = -20 240hrs note 1 note 4 operate at high temperature and humidity +40 , 90%rh 240hrs note 4 thermal shock -30 /30 min ~ +80 /30 min for a total 100 cycles, start with cold temperature and end with high temperature. note 4 vibration test frequency range:10~55hz stroke:1.5mm sweep:10hz~55hz~10hz 2 hours for each direction of x. y. z. (6 hours for total) mechanical shock 100g 6ms,x, y, z 3 times for each direction package vibration test random vibration : 0.015g*g/hz from 5-200hz, -6db/octave from 200-500hz 2 hours for each direction of x. y. z. (6 hours for total) package drop test height:60 cm 1 corner, 3 edges, 6 surfaces electro static discharge 2kv, human body mode, 100pf /1500? note 1: ta is the ambient temperature of samples. note 2: ts is the temperature of panels surface. note 3: in the standard condition, there shall b e no practical problem that may affect the display function. after the reliability test, the prod uct only guarantees operation, but dont guarantee all of the cosmetic specification. note 4: before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature. free datasheet http://
chimei inno l u x date :2011/04/28 page:17/20 6. general precautions 6.1. safety liquid crystal is poisonous. do not put it in your mouth . if liquid crystal touches your skin or clothes, wash it off immediately by using soap and water. 6.2. handling 1. the lcd panel is plate glass. do not subject the pane l to mechanical shock or to excessive force on its surface. 2. the polarizer attached to the display is easily da maged. please handle it carefully to avoid scratch or other damages. 3. to avoid contamination on the display surface, do no t touch the module surface with bare hands. 4. keep a space so that the lcd panels do not touch o ther components. 5. put cover board such as acrylic board on the surface of lcd panel to protect panel from damages. 6. transparent electrodes may be disconnected if you use the lcd panel under environmental conditions where the condensation of de w occurs. 7. do not leave module in direct sunlight to avoid malfunction o f the ics. 6.3. static electricity 1. be sure to ground module before turning on power or operating module. 2. do not apply voltage which exceeds the absolute maxi mum rating value. 6.4. storage 1. store the module in a dark room where must keep at 2510 and 65%rh or less. 2. do not store the module in surroundings contai ning organic solvent or corrosive gas. 3. store the module in an anti-electrostatic container or bag. 6.5. cleaning 1. do not wipe the polarizer with dry cloth. it migh t cause scratch. 2. only use a soft sloth with ipa to wipe the polarize r, other chemicals might permanent damage to the polarizer. free datasheet http://
chimei inno l u x date :2011/04/28 page:18/20 7. mechanical drawing free datasheet http://
chimei inno l u x date :2011/04/28 page:19/20 8. package drawing 8.1 packaging material table no. item model (material) dimensions(mm) unit weight (kg) quantity remark 1 lcm module EJ080NA-05B 183.0 141.0 5.6 tbd 30pcs 2 partition bc corrugated paper 512 349 226 1.184 1set 3 corrugated bar b corrugated paper 349 186 38 0.155 4pcs 4 dust-proof bag pe 700 530 0.060 1pcs 5 a/s bag pe 220.0 200.0 0.2 0.003 30pcs 6 carton co rru ga t e d pap e r 530 355 255 1 . 1 00 1 p c s 7 total weight tbd5% 8.2 packaging quantity total lcm quantity in carton: no. of partition 2 rows quantity per row 15 = 30 free datasheet http://
chimei inno l u x date :2011/04/28 page:20/20 8.3 packaging drawing free datasheet http://

▲Up To Search▲

Price & Availability of EJ080NA-05B

	To Download EJ080NA-05B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .